某会议室夏季工况不同送风方式下的气流组织数值模拟研究

采用数值模拟软件对××大学科技馆某小型会议室进行数值模拟,以实际测量的数据为边界条件,建立合适的数学和物理模型,得到温度场、速度场以及空气品质场等模拟结果,通过对模拟结果的对比分析,得到了最佳的气流组织设计方案,相关结论可以为室内气流组织方案设计与优化提供参考依据。     

涪陵地区茅三段热液白云岩展布影响因素分析

针对热液白云岩展布非均质性强的问题,开展基底断裂与茅三段沉积演化关系研究,分析断裂样式与白云岩分布关系,建立沉积演化模式,预测白云岩的分布。研究结果表明:茅三段可划分为5个小层,1~3小层为白云岩发育主要时期,4~5小层为台地均一化时期,不发育白云岩;15-1、15-2和16号基底断裂控制了早期“台-洼”相间的沉积地貌,断裂附近的地貌高部位为生屑滩发育有利部位,为白云岩的发育提供物质基础;15-1、15-2号基底断裂样式为花状,周边生屑滩白云石化程度高,为白云岩发育最有利区;16号基底断裂为直立状,附近白云石化发育程度较低,为白云岩发育较有利区。研究成果可为热液白云岩领域的进一步勘探提供指导依据。     

Estimating long-term time-resolved indoor PM2.5 of outdoor and indoor origin using easily obtainable inputs

To evaluate the separate impacts on human health and establish effective control strategies, it is crucial to estimate the contribution of outdoor infiltration and indoor emission to indoor PM_2.5 in buildings. This study used an algorithm to automatically estimate the long-term time-resolved indoor PM_2.5 of outdoor and indoor origin in real apartments with natural ventilation. The inputs for the algorithm were only the time-resolved indoor/outdoor PM_2.5 concentrations and occupants’ window actions, which were easily obtained from the low-cost sensors. This study first applied the algorithm in an apartment in Tianjin, China. The indoor/outdoor contribution to the gross indoor exposure and time-resolved infiltration factor were automatically estimated using the algorithm. The influence of outdoor PM_2.5 data source and algorithm parameters on the estimated results was analyzed. The algorithm was then applied in four other apartments located in Chongqing, Shenyang, Xi'an, and Urumqi to further demonstrate its feasibility. The results provided indirect evidence, such as the plausible explanations for seasonal and spatial variation, to partially support the success of the algorithm used in real apartments. Through the analysis, this study also identified several further development directions to facilitate the practical applications of the algorithm, such as robust long-term outdoor PM_2.5 monitoring using low-cost light-scattering sensors.     

Effects of ultrasound-assisted resting on the qualities of whole wheat dough sheets and noodles

The effects of resting under ultrasonic treatment on the properties of whole wheat dough sheets and noodles were investigated. Compared with the control group, the resting time to reach the maximum breaking force and extensibility of whole wheat dough sheets treated with ultrasound was shortened by 20 min. The proportion of strongly bound water (T₂₁) decreased, while the proportion of weakly bound water (T₂₂) increased during resting, and the ultrasonic treatment could accelerate this moisture redistribution in the dough. The extent of the increase in gluten macropolymer and the decrease in –SH content of ultrasound-treated wheat dough was higher than that of the control one during the initial 5–15 min resting, which could be related to the improvement of whole wheat dough extensibility. Whole wheat noodles showed a better breaking distance for 10 min of ultrasonic-assisted resting. Ultrasonic treatment could be used to reduce the resting time of whole wheat dough sheets and improve the texture properties of noodles.     

Investigating measurements of fine particle (PM2.5) emissions from the cooking of meals and mitigating exposure using a cooker hood

There is growing awareness that indoor exposure to particulate matter with diameter ≤ 2.5 μm (PM_2.5) is associated with an increased risk of adverse health effects. Cooking is a key indoor source of PM_2.5 and an activity conducted daily in most homes. Population scale models can predict occupant exposures to PM_2.5, but these predictions are sensitive to the emission rates used. Reported emission rates are highly variable and are typically for the cooking of single ingredients and not full meals. Accordingly, there is a need to assess PM_2.5 emissions from the cooking of complete meals. Mean PM_2.5 emission rates and source strengths were measured for four complete meals. Temporal PM_2.5 concentrations and particle size distributions were recorded using an optical particle counter (OPC), and gravimetric sampling was used to determine calibration factors. Mean emission rates and source strengths varied between 0.54—3.7 mg/min and 15—68 mg, respectively, with 95% confidence. Using a cooker hood (apparent capture efficiency > 90%) and frying in non‐stick pans were found to significantly reduce emissions. OPC calibration factors varied between 1.5 and 5.0 showing that a single value cannot be used for all meals and that gravimetric sampling is necessary when measuring PM_2.5 concentrations in kitchens.     

Transient Simulation of Hollow‐Fiber Membrane Filtration with Nonuniform Permeability Distribution

Transient simulation of filtration in hollow‐fiber membranes with nonuniform permeability distribution was conducted. The diversity of permeability distributions caused different initial flux and transmembrane pressure distributions. Manipulating the permeability distribution enables a hollow‐fiber membrane to achieve its maximum volumetric flow rate. During solid‐liquid separation, the inter‐adjustment between flux and cake distributions improved their uniformities simultaneously. The reciprocal of the volumetric flow rate of the membranes all increased linearly with water production. Severely nonuniform permeability distribution caused low water production. The numerical results could be applicable to account for the non‐ideal performance of industrial hollow‐fiber membrane modules.     

Numerical simulation analysis and experimental validation on wear/fracture mechanisms of polycrystalline cubic boron nitride superabrasives in high-speed grinding

In this study, a two-dimensional finite element model is proposed to investigate the wear/fracture mechanisms of polycrystalline cubic boron nitride (PCBN) superabrasives in high-speed grinding process. The special geometric microstructures of PCBN grains are constructed by using the classic Voronoi tessellation technique, and cohesive elements are embedded into the geometric model of PCBN grains as the potential crack propagation paths for simulating the wear/fracture behaviours of PCBN grains under grinding loads. The effects of uncut chip thickness per grain (a_gmax) on the stress distribution characteristics and wear/fracture behaviours of PCBN grains during grinding are discussed in detail. Results show that the wear behaviour of PCBN grains during grinding mainly occurs around the grain vertex region; however, the fracture behaviour, leading to the quick failure of PCBN grains, is prone to appear around the grain–filler bonding interface, which is usually on the opposite side of the in-feed direction. Moreover, to separate the PCBN grains from the macro-fracture during grinding, the uncut chip thickness per grain should be kept smaller than 1.0?µm to prevent the unfavourable fracture behaviour from appearing around the grain–filler bonding interface. Furthermore, the corresponding single-grain grinding trials are performed to validate the numerical simulation results by evaluating the wear/fracture morphologies of the PCBN superabrasives in the actual grinding operation.     

钢制导热油烘缸的数值模拟与结构优化

针对钢制导热油烘缸在工作时出现工作表面温度分布不均匀、温差大等情况，采用三维建模和模拟仿真方法对钢制导热油烘缸的结构进行优化。本研究主要从3个方面对钢制导热油烘缸进行结构改进，分别是改变循环油路通道数量，改变进油槽与出油槽上孔的排列方式，改变循环油路的结构。研究结果表明，相对其他烘缸结构，具有循环油路通道数量为20个、进油槽与出油槽上孔为单排排列、循环油路两两相通的钢制导热油烘缸的性能更好，可以达到工作表面温度分布均匀、温差控制在±5℃以内的目的。